Uzzors2k Banner

15 - 48V Bench SMPS

15 - 48V Bench SMPS

Since I started with my first flyback driver I wanted a proper power supply. A few years later I had the experience required to make one, and here it is. This is basically a step-up again from the multi-purpose inverter. It provides adjustable regulated DC voltage between 15 - 48V, and short-circuit protection which kicks in at 14A. An all-around bench supply in other words.


The circuit operation is pretty straight-forward, and very modifiable. The output voltage is compared with a stable reference voltage, and based on the error the TL494 adjusts the duty cycle to compensate. The output from the TL494 drives a BJT full-bridge, which drives the gate drive transformer (GDT). The GDT controls the IRFP450 power mosfets. The IRFP450s are in a half-bridge configuration and run the main power transformer at the duty cycle decided by the TL494 chip. The output from the main power transformer is rectified and filtered, and finally the output voltage is measured again by the TL494. This is called closed-loop operation. Each section of the circuit is dicussed further down. I've made an open-office spreadsheet to aid modification or design, and all of the math I required is in it I believe. Just ask if something is missing.

Front panel

PWM Generation and Overcurrent detection Section
In my experience the logic section with GDT and fan(s) consumes about 15W +/- 5W. Keep this in mind when looking for a small 16V power source. Iron-cored wall warts work well for this purpose. Pin 14 on the TL494 generates a regulated 5V output, which is used for providing a stable reference voltage. I do not use it for the 5V source in the comparator section, as I don't want to load it down. One of the error amps on the TL494 is used to determine the duty cycle. The reference is divided by 2 with two 15k resistors and fed to pin 2 giving a 2.5V reference. The output voltage from the supply is sent through a divider as well, and depending on the potentiometer setting will provide an output voltage of 2.5V at different voltages (15-48V). With low resistance the ratio is low and it only takes 15V before the divider output is 2.5V, high potentiometer resistance results in a large ratio and high voltage required before 2.5v is reached. From pin 3 to pin 2 is a gain compensation network, consisting of a capacitor and resistor. The purpose of this is to stabilize the control loop, and it's design is far too complex for amatures to understand. (I haven't even tried.) All you need to know is that the capacitor's impedance will vary with frequency, in effect giving a frequency dependent resistor. This coupled with the 180k resistor gives the error amp frequency dependent gain, allowing for stabilization depending on the load, duty cycle and frequency. Like I said, you don't want to know.

PWM board

The overcurrent detection works by sensing current with a shunt resistor, which is a resistor from your load to real/circuit ground. Thanks to Ohm's Law (U=R*I  <--this is too easy) we know that with a set current and resistance, the voltage developed across the resistor is known. Just a note to the circuit, power ground is the negative lead out from your supply, you can't use ground as the negative supply lead if you want overcurrent protection. The voltage developed across the resistor is fed through an RC filter which slows it down and keeps the mean value, and later amplified by the first op-amp. Amplification reduces the voltage needed across the resistor, which greatly reduces it's losses. The gain of the first op-amp is set with the 3 resistors around it (39k, 2.2k and 100R) and depending on the gain different overcurrent levels can be chosen. The second op-amp acts as a comparator and trips the small SCR when the current limit is exceeded, lighting the warning LED at the same time. Just like with the TL494 error amp you set a reference voltage on the inverting input with a voltage divider, and feed the signal into the non-inverting input. The funky dual LED will light one of it's didoes when an overcurrent condition occurs, while the other diode will lose power since it's powered from the main supply.

Gate Drive Section
The output section in the TL494 consists of two transistors, which cannot drive a transformer directly. So by using some pull-up resistors it can drive a full-bridge of small BJTs, which can then drive a GDT. The design of the full bridge and TL494 outputs is such that during deadtime both primary leads of the GDT will be held low. This is equivalent to shorting the core, which resets it and allows for flawless duty cycle generation through a transformer. Toroidal ferrite cores with high Al value and decent cross-sectional area (50-100mm^2) are excellent for GDT creation. At low frequency operation such as this quite a few turns are required. Although the voltage stand-off isn't optimal, and some cores are sharp enough to scratch off enamel I've used magnet wire for winding my GDT. In high frequency applications I use multi-strand coax cable, which gives the best performance. See how you feel about the core and safety when you choose materials. James Pawson has a great site on GDT making (among other things).

Lash up testing

POWER Section
Rectified mains is filtered (this is optional) mainly to keep noise from the supply from traveling back up mains and disturbing other appliances. I built an unregulated and sloppy SMPS for an amplifier before this project, without a filter of course, and whenever I turned it on my brother's amplifier in another room would start humming. So yes, it is somewhat important. Mains is rectified with a beefy bridge and filtered with a large storage capacitor. Between the bridge and capacitor is a NTC. NTCs have a negative thermal coefficient, hence the name. What they do is have low resistance at high temperature, and high resistance at low temp. In this circuit one is used to limit the inrush current to the man filter capacitor. Since a large capacitor will provide a substantial load when empty, it can draw enough current when starting up the PSU to blow fuses or a breaker. The NTC prevents this by limiting the initial current, and slowly letting more through as it heats up. The problem is that when drawing 500W or more large NTCs are needed which aren't easy to find or very practical, so the NTC can be omitted. If the filter capacitor causes your breaker to trip use a light-bulb/switch like in my MKII multipurpose inverter. The two 120k resistors simply bleed away charge on the filter capacitor when the supply is turned off.

From the GDT outputs come alternating square-wave pulses 180 degrees out of phase, which control the IRFP450s. Together with the two 3µF capacitors they form a half-bridge, which sends alternating current through the main power transformer. The two 3µF capacitors will carry all of the load current, and should be polypropylene foil type capacitors. Some designs use electrolytics for the half-bridge and filter capacitors in one, but I've found that the electrolytic heat up and eventually fail when used this way. The amount of average current sent through the transformer is controlled by the duty cycle, which is controlled by the TL494. The secondary is center-tapped so dual diode rectification can be use. For filtration of the rectified output a 33µH inductor and 1000µF capacitor are used. The double 400V 16A rectifiers seem to be overkill, but I found them necessary. They were reasonably cheap anyway. Experiments with 60V Schottky diodes resulted in plenty of failures for some unknown reason, so I would go no lower than 100V, and rate the diodes generously for the current. This is your workhorse remember!

The power transformer itself was put together from an old ATX core, which is ideal since they are used in this exact same fashion and frequency. They might not be large enough for continuous operation at more than 300W, but enough to last shorter runs at twice that. A good question is how to design a transformer for 750W operation. What limits power in transformers is how much power they can dissipate. A core can lose power through losses tied to drive frequency and/or magnetic flux being too high, but that's about it unless I'm mistaken. The other losses are copper losses from the windings, and ideally you want to fill the entire window area with copper to reduce the resistance as much as possible. So if you can the required number of turns in at the required thickness in the winding area, the core is large enough. The resistance of the wires, even if only 0.5 ohms can drop a decent amount of voltage. Now the DC resistance might seem low, but remember that the skin effect kicks in too, increasing the effective AC resistance. At 45kHz, for 16A capable wire I would use four strands of 22AWG twisted together as litz wire. The primary only has to handle about 4-5A at full load, so bifilar 22AWG should be enough. 

ATX power transformer
For further reference see these projects. They were of great use during the design process of my bench supply.
Similar Projects

A KW Switch Mode Regulated High Voltage Power Supply
250 W S.M.P.S. with Power FETs

Youtube Flickr Twitter LinkedIn To top

Disclaimer: I do not take responsibility for any injury, death, hurt ego, or other forms of personal damage which may result from recreating these experiments. Projects are merely presented as a source of inspiration, and should only be conducted by responsible individuals, or under the supervision of responsible individuals. It is your own life, so proceed at your own risk! All projects are for noncommercial use only.

Creative Commons License This work is licensed under a Creative Commons Attribution-Noncommercial-Share Alike 3.0 Unported License.